![]() ![]() Overall, I’m really pleased with this, and the quality of the LED lights is good. The biggest issue with this overall design is that you can’t easily open the frame up again without replacing the framing tape. The trickiest bit is cutting the wooden dowelling to size – you need to make each piece the same size. The things you need for the A4 version I built are:Īdditionally, I used a piece of A4 black card, and you’ll need some masking tape, sandpaper, some pliers and a small hacksaw. The video above shows how I built it, and it’s pretty simple. I decided to use an IKEA Ribba frame because they’re naturally very deep and so could accommodate some LED lightstrips inside it. I was thinking of ways to display it, and decided that it would be fun to build a lightbox. After you have checked to make sure it works, open up the LEGO frame and add the switch to the empty space you left for it.I recently went to the Stanley Kubrick exhibition at The Design Museum, and I came away with this transparency reproduced from 2001: A Space Odyssey. Before you put the switch into your LEGO frame, check the connection and make sure that switch properly turns the LEDs on and off. I found that using a clamp to hold the switch in place while I solder was very helpful. Once you have removed the thin coating of plastic, you can go ahead and solder everything together. If you do not sand off the plastic, the solder will not stick to the wires. However, before you can do this you MUST sand the ends of the wires with some fine sandpaper because there is a very thin coating of plastic around the wires. Using a discarded flat screen tv, a slat from a timber venetian blind, some LED strip lighting and some hot glue sticks I made an awesome back lit picture fr. Next, you'll want to solder both ends of the wire you just cut to the switch. This is where you will insert the switch. Once you find it, turn them off again, and clip either one of the wires (positive or negative) leading to the LED a couple of inches before it. Turn on your battery powered LED strip and locate the first LED on the strip (the one closest to the battery pack). Remember, this is how I constructed my frame, you however can create whatever size and shape frame you would like. If you happen to find a switch that fits perfectly in your LEGO frame, that’s great! You can skip right ahead to Step 4. If you’re using the switch I used you will need to leave a space that measures slighlty taller (actually 2 tile bricks taller) than a standard 2x2 brick and use a Dremel (See step 3) to shave off the LEGO bricks to the left (or right) of the space for the switch. (See photos.) Be sure to leave some room for the switch that you’ll be putting in later. Then add a layer of smooth tile pieces on top trying to keep everything the same color. Also, make the thin backing extend into the frame a little bit at the bottom to create a "pouch" that will later help hold the battery pack inside the frame. Add a thin layer of flat LEGO plates to the back of the frame to ensure that it will be secure. Using LEGO bricks with a width of 2 studs, construct a 34x26-stud lego frame that measures 2 bricks tall. When the LEDs are on, the light will shine through your design, causing it to omit and elegant glow and make you smile every time you walk by. Then, with the aid of an electronic cutting machine, you create a design of your choice and adhere it to the frame. Basically, you construct a frame of LEGOs, whatever size and shape you choose, and add a switch to the frame and connect it to the LEDs. You can change everything from the design on the front, to the color(s) of the frame and/or LEDs, and even the size and shape of the frame! You could light-up the logo of your favorite fandom, make your favorite quote shine like never before, or even display your own unique work of art to brighten up your bedroom! The possibilities are endless!Īlso, this project is fun and easy to make! Not too skilled at woodworking? No problem! Oddly enough, the main ingredient to this frame is LEGO bricks! The structure of this project is quite simple actually. ![]() This makes a great project for several different reasons but mainly because it very customizable. Today, I am going to show you how to make your very own backlit poster. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |